¡Precio rebajado! BLUETOOTH HC-08 BLE 4.0 Ver más grande

MODULO BLUETOOTH HC-08 BLE 4.0

BTHC08

Nuevo producto

Los equipos de Apple aceptan la conexión con este tipo de módulos versión 4.0 del Bluetooth  y rechazan las versiones previas como la 2.0.

Más detalles

Este producto ya no está disponible

6,93 € impuestos inc.

>-30%

9,90 € impuestos inc.

Más

Este módulo HC-08 se puede utilizar directamente para enviar y recibir mensajes a través del Bluetooth sin más que pinchar sus pines serie Rxd y Txd a los correspondientes de nuestro Arduino y con el programa adecuado no necesitamos más.

Podemos hacer un pequeño montaje para entrar en modo de comandos AT y probar  la comunicación con el modulo Bluetooth. Para ello basta con arrancarlo mientras mantenemos en HIGH su pin ENABLE. La conexión es completamente similar a la que usamos con el modulo HC_06.

Características:

  • Protocolo de bluetooth: Especificación Bluetooth V4.0 ble,
  • Medio abierto y el iPhone 4 s puede alcanzar 110 metros distancia comunicación.
  • Chipset basado en ti CC2541
  • Bluetooth Clase 2
  • Nivel industrial módulo Bluetooth SPP
  • Antena de chip integrado
  • Tamaño: 26.7x13x2mm
  • Industrial Rango de temperatura de-40 a + 85
  • Soporte para aplicaciones de a bordo
  • Frecuencia de operación: 2.4 GHz ISM Band
  • Método de modulación: GFSK (gaussian Frequency Shift keying)
  • Agudeza:-84 dBm o menos BER a 0.1%
  • Velocidad de transferencia: asíncrono: 6 kbps síncrono: kbps
  • Características de seguridad: autenticación y cifrado
  • Servicios de apoyo: central y periférico UUID ffe0, FFE1
  • Consumo de energía: modo de suspensión automático, la corriente de espera 400 ~ 1.5 ma, la transferencia de 8.5 ma.

AT commands & Configuration

1) Query the native MAC address
Send: AT + ADDR?
Send after a successful return: OK + LADD: MAC address (address for 12 string)

2) Query the baud rate
Send: AT+BAUD?
Send after a successful return: OK + Get: [para1]
Scope of para1:0 ~ 8. The parameters corresponding to: 0 represents 9600, 1, 2, 9600, 38400, on behalf of the representative representative of 57600, 115200, 5, 4800, 6, 7 represents 1200, 1200 2400. The default baud rate to 9600.

3) Set the baud rate
Send: AT+BAUD[para1]
Send after a successful return: OK+Set:[para1]
Example: send: AT + BAUD1, return: OK + Set: 2.The baud rate is set to 19200.
Note: after the switch to the 1200, module will no longer support the configurations of the AT command, and press the PIO0 under standby, module can restore the factory Settings.Do not recommend using the baud rate.After setting the baud rate, modules should be on electricity, anew set parameters can take effect.

4) from the device connected to the bluetooth address specified
Send: AT+CON[para1]
Send after a successful return: OK+CONN[para2]
Para2 range is: A, E, F
Example: from the bluetooth address is: 0017EA0943AE, sending the AT + CON0017EA0943AE, module returns: OK + CONNA or OK + + CONNF CONNE or OK.

5) removal equipment matching information
Send: AT + CLEAR
Send after a successful return: OK + CLEAR
Clear success had connected device address code information.

6) query module working mode
Send: AT + MODE?
Send after a successful return: OK + Get: [para]
Para: the range of 0 ~ 2. 0 represents passthrough mode, on behalf of the PIO acquisition + remote control + 1 passthrough, 2 representative passthrough + remote control mode.The default is 0.

7) set module working mode:
Send: AT + MODE []
Send after a successful return: OK + Set: [para]

8) query device name
Send: AT + NAME?
Send after a successful return: OK + NAME [para1]

9) set the device name
Send: AT + NAME [para1]
Send after a successful return: OK + Set: [para1]
Example: Set the device name to Seeed, sending the AT + NAMESeeed, return OK + Set: Seeed AT this time, the name of the bluetooth module has been changed to Seeed. Note: after the instruction execution, required to electricity, set the parameters of the approval.

10) query matching password
Send: AT + PASS?
Send after a successful return: OK + PASS: [para1]
Para1 range is 000000 ~ 999999, the default is 000000.

11) pairing set password
Send the AT + PASS [para1]
Send after a successful return: OK + Set: [para1]

12) restore factory Settings
The AT + RENEW send
Send after a successful return: OK + RENEW
Restore the default factory Settings module, the module Settings will be reset so, back to the factory with the status of the factory default, delay module 500 ms after the restart.If no need, please be careful.

13) module reset
Send: AT + RESET
Send after a successful return: OK + RESET
After the instruction execution module will delay 500 ms after the restart.

14) set the master-slave mode
Send: AT + ROLE [para1]
Send after a successful return: OK + Set: [para1]

Reseñas

Escribe tu opinión

MODULO BLUETOOTH HC-08 BLE 4.0

MODULO BLUETOOTH HC-08 BLE 4.0

Los equipos de Apple aceptan la conexión con este tipo de módulos versión 4.0 del Bluetooth  y rechazan las versiones previas como la 2.0.

651470183

Envios 24/72H

info@bricotronica.com

Gratis a partir de 150€